Semi-permanent Kit
with lamp and accessories
WHAT THE KIT INCLUDES:
BASE
TOP
3 COLORS:
- color SA45 Chanel Red
- color SA68 Rosino![]()
- color HF01 Black
48w LED lamp , with timer, LCD display and hand presence sensor
Accessories: all the useful accessories to complete your manicure
FLUID PRO 100ml
100 Aluminum Foil Removal
_
> In the ATTACHMENTS section you can download the PDF with the instructions <
_
Watch our video tutorials:
HOW TO APPLY SEMI-PERMANENT
SEMI-PERMANENT REMOVAL
USE
Nail preparation Accessories: Gloves - File - Nipper - Finishing block - Cuticle pusher - Pressed cotton pad - Disinfectant - FluidPro®
Let's put on our gloves and get started.
1 We spray the instruments and the client's hands with the disinfectant. We dry the hands well with a towel.
2 Using the nippers, we cut off the excess cuticles
3 Push back the small cuticles along the perimeter of the nail, using the cuticle pusher or the orange stick
4 We use the file (side 180) to give the nails the preferred shape
5* Take the finishing block and evenly mattify the nail
6* Now with a cotton pad moistened with FluidPro, we clean the surface of the nail from dusty residues
Application of Semi-permanent LCI
Accessories: Color - Base - Top - Pressed cotton pad - Cleaner - FluidPro® - UV or LED lamp - Cuticle oil
7* Apply a THIN and EVEN layer of Base, taking care not to touch the cuticles
8* Catalyze in UV lamp for 120 sec. (in LED lamp 60 sec.)
9 Now, with a DRY pad we eliminate the dispersion released by the Base, passing it over the surface of the nail. Don't be afraid, let's do it decisively.
What is dispersion? Dispersion can be given by both Base and Top. It is a thin and sticky layer caused by the excessive amount of product applied.
10* Apply the first layer of color (we recommend 3 layers in total). Here too, try not to dirty the cuticles and apply it evenly and thinly. Catalyze in a UV lamp for 120 sec. (in a LED lamp 60 sec.) REPEAT THIS POINT 3 TIMES (3 layers of color)
11 Now we are ready to apply the Top. We make a homogeneous, thin layer and catalyze in a UV lamp for 240 sec., i.e. 2 timer cycles (in a LED lamp 120 sec.).
12* Take a small square of pressed cotton wool, moisten it with the Cleaner and clean the surface from the Top dispersion.
13 At this point we can apply the cuticle oil, distributing a small amount on the perimeter of each nail. We gently massage the fingers and congratulations, we have finished our semi-permanent manicure!
HELPFUL TIPS
5* Be careful not to leave any part of the nail shiny. Always check against the light that the surface is completely opaque.
6* Be careful, after completing this process, never touch the nail again for any reason, we could grease it again and this will create possible problems with future holding.
7* Do not leave any part of the nail uncovered by the base. Check, here too, by looking at the surface against the light. I recommend that it is a thin layer, otherwise, a thick layer could cause problems with the duration of the color and excessive dispersion.
8* Let's be careful to position our hand well, so that all our fingers are uniformly facing under the beam of the light bulbs. Let's not bend our thumb much but try to stretch it as best we can.
10* We must not rush to see a completely covering effect right away, let's finish all the steps well. If we dirty the cuticles or the skin, clean with the orange stick moistened with FluidPro before catalyzing in the lamp.
12* To eliminate the dispersion of the Top, we can also use the FluidPro instead of the Cleaner. But be careful, in this case the passage on the surface of the nail must be quick and light to avoid dulling the result.
IMPORTANT: Apply the product (base, color, top) also on the tip of the nail before catalyzing in the lamp (CLOSURE AT THE TIP technique). This will ensure a long-lasting polish.
Store Locator
